Your air conditioner runs eight to ten months a year in Florida, and an under-insulated attic makes every one of those months more expensive. On a summer afternoon, the attic itself can top 120 degrees. If the insulation up there is thin, patchy, or decades old, that heat moves through the ceiling and into the rooms below all day long. Blown-in insulation from TIES 360 adds a thick, even layer above your ceilings that slows the heat down, so the AC cycles less and your rooms hold their temperature.
Blown-in insulation, also called loose-fill, is made of small particles blown through a hose into attics and other spaces that are hard to reach with rolled batts. It fills the gaps around wiring, plumbing, and framing that batts leave exposed, and it goes in without tearing open a single wall or ceiling.
The same four steps for every job we do, from duct cleaning to attic insulation.
Contact us and tell us what's going on. We'll set a time that works for you.
A technician inspects the problem area, takes measurements, and shows you what they find.
The price in writing before any work starts. No pressure either way. You'll receive a hassle-free esimate.
Same crew, on schedule. We keep the job contained and leave your home cleaner than we found it.
The Department of Energy recommends R-49 to R-60 for an uninsulated attic in our part of Florida, and a top-up to at least R-38 where some insulation is already in place. R-value measures how well a material resists heat, and in practice it comes down to depth: the higher the number, the thicker the layer. There’s a quick check you can do from the attic hatch with a flashlight. If you can see the tops of the ceiling joists poking through the insulation, the layer is thin and almost certainly below those numbers. We measure what’s actually up there, tell you the R-value you have now, and quote what it takes to close the gap. If your attic is already close to right, we’ll say so.
The work is simpler than most homeowners expect. We start with a walkthrough of the attic to catch anything that needs attention first: air leaks around fixtures, a bathroom fan venting into the attic instead of outside, recessed lights that need clearance. The blowing machine stays outside with the truck, and a hose runs up through the attic hatch. One technician feeds the machine while another works the hose, building an even layer to the target depth. Depth markers in the attic show the finished level, so you can climb up and check it yourself any time. Floors under the hatch get covered, and the crew cleans up before they go.
Not every attic just needs more insulation. Some need the old material taken out first. Roof leaks and storm damage leave insulation wet and matted. Rodents nest in it. Older material settles until it insulates far below its original rating. Our crew removes damaged or contaminated insulation with vacuum equipment built for the job, bags it before it moves through your house, and preps the attic for a clean new layer at the right depth. If your home has had a roof leak, a pest problem, or a major renovation, have the attic checked before anything new goes on top.
TIES 360 is based in Sarasota and has worked on indoor air quality here for more than 20 years. Our NADCA-certified technicians install, remove, and replace blown-in insulation across Sarasota and Manatee counties: Sarasota, Bradenton, Lakewood Ranch, Venice, Siesta Key, Longboat Key, University Park, and the communities around them. The attics vary more than you’d think. Insulation is also one part of how we treat the house as a whole, because what’s in your attic affects what your AC costs to run and what ends up in the air you breathe.
Usually, yes. If the existing material is dry, clean, and lying flat, we top it up to the target depth. If it’s wet, moldy, or has had pests in it, the old layer comes out first. We check before we quote, so you’ll know which situation you’re in.
It depends on the size of the attic, how much insulation is already up there, and whether old material has to come out first. A straightforward top-up costs far less than a removal and replacement. We measure first and quote from what your attic actually needs rather than a square-foot guess over the phone.
It should. ENERGY STAR estimates an average savings of 15% on heating and cooling costs from air sealing plus added insulation. Your number depends on how thin the current layer is and what shape your ducts are in, which is why we measure before we promise anything.
Most top-ups are finished in a day, often in a morning. Removal and replacement usually runs one to two days depending on the attic. You’ll get a timeframe with your quote.
The material lasts for decades. What shortens its life in Florida is moisture from roof leaks, pest activity, and gradual settling. If your insulation went in before the 2000s, have the depth measured, because settling alone can pull it well below its original R-value.