Blower Door Tests In Florida

You’re planning to move to the great state of Florida soon, and you’re having a new home built there. Before construction is complete, you wonder if you have to schedule a blower door test to detect air leakages. Is a blower door test mandated in Florida, or are you okay going without?

Since July 1st, 2017, any new construction of residential property in Florida must undergo a blower door test to ensure the home is up to the current energy code. This change is part of the Florida Building Code, 6th Edition, and is outlined in Section 402.4.1.2.

There are also some exclusions about who in Florida might require blower door tests. Here are the two exceptions:

  • “Section R402.4 states that dwelling units of R-2 Occupancies and multiple attached single family dwellings are permitted to comply with Section C402.5 of the commercial provisions of the Florida Energy Code. Section C402.5 allows thermal envelope leakage compliance via either a list of prescriptive requirements or through air leakage testing.
  • Section R402.4.1.2 lifts the testing requirement for additions, alterations, renovations or repairs to an existing home’s building thermal envelope if the new construction is less than 85 percent of the thermal envelope.”

Failing the Blower Door Test Will Cost You

You’re eager for your new construction home in Florida to pass its blower door test. Leesburg, Florida news resource Daily Commercial said in a 2017 article that if your home doesn’t pass, you might have to get mechanical ventilation for the home, which will improve the air quality.

Although mechanical ventilation will make it easier to breathe, both literally and figuratively, that peace of mind comes at a price. Fixr quotes the cost of a mechanical ventilation system at $500 to $8,000. Then you have to pay for installation, which might cost between $50 and $150 an hour. Adding that up, the installation costs could run $1,200 to over $8,500.

How Do You Pass a Blower Door Test?

So, how does your house pass a blower door test? Per Florida Building.org, the rules are as follows: “The building or dwelling unit shall be tested and verified as having an air leakage rate not exceeding seven air changes per hour in Climate Zones 1 and 2, and three air changes per hour in Climate Zones 3 through 8.”

In Table 402.4.2, Air Barrier and Insulation Inspection Component Criteria, here is what’s required of you to pass a blower door test in Florida.

  • Fireplaces: Your fireplace must have an air barrier.
  • HVAC register boots: Any HVAC register boots that penetrate the building envelope must be sealed to either the drywall or the subfloor.
  • Common wall: The common wall(s) between any dwelling units require air barrier installation.
  • Exterior wall phone/electrical box: For exterior walls with a phone or electrical box, you have two options. You can either get air-sealed boxes or ensure that the current air barrier goes beyond the boxes.
  • Exterior wall tub or shower: A tub or shower installed on an exterior wall requires an air barrier between the fixture and the exterior wall.
  • Wiring and plumbing: All wiring and piping need some form of insulation, be that blown or sprayed insulation or batt insulation. The insulation should be installed around the plumbing or wiring and beyond.
  • Recessed lighting: If your recessed lighting fixtures are not installed in a conditioned space, then they must be sealed to the drywall. The fixtures must also have an Insulation Contact (IC) rating.
  • Garage separation: The space between conditioned spaces and your garage must have air sealing.
  • Narrow cavities: Any narrow cavities in the new home construction must have blown insulation, spray insulation, or batts.
  • Penetrations and shafts: From flue shafts to knee walls, utility penetrations, and duct shafts, if these are around an unconditioned or exterior space and they’re open, they have to be sealed.
  • Crawl space walls: The crawl space walls must have permanent insulation. If there’s any exposed earth around the crawl space, it must have a Class I vapor retarder. You also have to tape up any overlapping joints.
  • Floors: All floors, especially cantilevered and above-garage floors, must have insulation such that the subfloor decking’s underside makes contact with the insulation. If the insulation has any exposed edges, then an air barrier must be placed.
  • Rim joists: All rim joists must have an air barrier and be insulated.
  • Doors and windows: Any space from the frame to the door jamb or window must be sealed.
  • Walls: The sill plate and foundation junction must be sealed and all headers and corners should have insulation.
  • Attic and ceilings: Drop-down stairs, knee wall doors, and attics (except for unvented attics) need sealing. Soffits and drop ceilings should have an air barrier that’s aligned with the insulation. All gaps in these areas must be sealed.
  • Thermal barrier and air barrier: An air barrier’s air-permeable insulation cannot be used to seal a space, but it can go inside an air barrier. If the air barrier is broken in any way, it must be repaired or filled. The exterior thermal envelope insulation used for any frame walls and the building envelope air barrier must be aligned and in contact.

If you want to learn even more about the blower door testing requirements in Florida, you’ve come to the right place.

941-870-3302

TIES360, LLC

Let us help you breathe cleaner indoor air!

Would You Like to Learn More?

What questions can we answer for you?